|
Hi
thanks for the reply
I reinstall my linux and upgrade to 2.4.18 kernal with latest lvs stuff and
patch.
I confiure the script and run it.
This time , the rc.lvs_nat run nicely without any error occurs, I means
this time it didn't complain any error.
but I find the alias of the eth0:68 still disappear after running the
scripts , since I set the alias eth0:68 as dip, so my dip is lost. I think
the lost of the dip make my lvs down. Actually, I do nothing on iptables
setup, just run the rc.lvs_nat which complied from my lvs_nat.conf file.
I add another nic called eth1 (192.168.1.68) as the dip. but after runing,
my nat still didn't work.
I have set the default gw of the real server as the dip of the director.
I actaully use the same nic as yours Dlink530TX revB, ..... ;-)
Any ideas?
Regards
xiao
----- Original Message -----
From: <jlobascher@xxxxxxxxxxxxx>
To: <lvs-users@xxxxxxxxxxxxxxxxxxxxxx>
Sent: Thursday, April 18, 2002 2:39 PM
Subject: RE: LVS_NAT Doesn't work
I had a very similar problem with my LVS NAT - found that upgrading to
kernel.org 2.4.18 with IPVS patch version 1.0.0 fixed everything...
My problem turned out to be a buggy NIC driver in the RedHat supplied
kernel - NIC is a Dlink530TX revB...
Try a new kernel and IPVS and I think you will be in much better shape.
jeremy
-----Original Message-----
From: xgao@xxxxxxxxxxxxxxx [mailto:xgao@xxxxxxxxxxxxxxx]
Sent: Thursday, 18 April 2002 4:24 PM
To: lvs-users@xxxxxxxxxxxxxxxxxxxxxx
Subject: LVS_NAT Doesn't work
Hello Joe
Thanks for the reply, but I still have some LVS NAT problem.
Here is my diagram
________
# | |
# | client |
# |________|
# | CIP=eth0 192.168.1.4
# | __________
# | | |
# |------| director |
# | |__________|
# | VIP=eth0 192.168.1.10
# | DIP=eth0:68 192.168.1.68
# |
# |
# RIP=eth0 192.168.1.5
# _________|_____
# | |
# | realserver1 |
# |_____________ |
The client is a win2k
The director is a Pensacola Redhat enterprise server
The real server is a win2K runing apache listening 80 port
-------------------------------------------------
Here is my configure file
LVSCONF_FORMAT=1.1
LVS_TYPE=VS_NAT
INITIAL_STATE=on
CLEAR_IPVS_TABLES=yes
VIP=eth0 lvs 255.255.255.0 lvs
DIP=eth0:68 dip 192.168.1.0 255.255.255.0 192.168.1.255
DIRECTOR_GW=192.168.1.4
SERVICE=t 80rr rip:80
SERVER_NET_DEVICE=eth0
----------------------------------------------------
I run ./configure lvs_nat.conf and get the rc.lvs_nat file.
After I run the rc.lvs_nat, and type ipvsadm I can see
displaying ipvsadm settings
IP Virtual Server version 0.8.1 (size=65536)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP lvs:http rr
-> rip:http Masq 1 0 0
but when I use client to browse the 192.168.1.10, it can not display the
page. And I back to my linux, I find InActConn get one hit. If I refresh
the
client browser, InActConn will count to 2.
Actually, I have add the 192.168.1.68(DIP) as the default gateway of the
real server but it still doesn't work for me.
I follow your instruction to export rc.lsv_nat to a out file.
Here is the file.
looking for standard utilities
$ECHO=/bin/echo
$PING=/bin/ping -U -c 1
testing ping
ping can send one packet. is OK.
$FPING=/bin/ping -U -c 1
$IFCONFIG=/sbin/ifconfig
$NETSTAT=/bin/netstat
$ROUTE=/sbin/route
$AWK=/bin/awk
$AWK=/usr/bin/awk
$GREP=/bin/grep
$HOSTNAME_CMD=/bin/hostname
$UNAME_CMD=/bin/uname
$CAT=/bin/cat
$CUT=/bin/cut
$CUT=/usr/bin/cut
$TAIL=/usr/bin/tail
$XARGS=/usr/bin/xargs
$PS=/bin/ps
$KILL=/bin/kill
$WC=/usr/bin/wc
$TRACEROUTE=/usr/sbin/traceroute
$ARP=/sbin/arp
$ROUTE=/sbin/route
$TR=/usr/bin/tr
$EXPR=/usr/bin/expr
$CHMOD=/bin/chmod
$MV=/bin/mv
$RM=/bin/rm
$MKDIR=/bin/mkdir
$SSH=/usr/bin/ssh
$NTPD=/usr/sbin/ntpd
$IP=/sbin/ip
rc.lvs version 0.9.2 Aug 2001
(C) 2000-2001 Joseph Mack jmack@xxxxxxxx, distributed under GPL license
This file is part of the LVS project http://www.linuxvirtualserver.org
setting up pwLoadbalancer.patternware_cn
find_System_map
System.map
$SYSTEM_MAP=/boot/System.map
kernel series 2.4.9-26beta not handled by this code
you may get errors depending what you ask it to do.
supported are Linux 2.2.x and 2.4.x
Warning: kernel version not 2.2. or 2.4
$LSMOD=/sbin/lsmod
$RMMOD=/sbin/rmmod
$INSMOD=/sbin/insmod
number nics on director 1
LVS director
Error: kernel series 2.4.9-26beta not 2.2 or 2.4
setting default policy to ACCEPT for LVS devices
Error kernel series 2.4.9-26beta unknown
clearing iptables/ipchain rules
Error: kernel series 2.4.9-26beta unknown
set_director_ip_forwarding on vs-nat director (1 on, 0 off).
set ip_forward ON for vs-nat director (1 on, 0 off).
proc/sys/net/ipv4/ip_forward 1
director is gw for realservers: turn off icmp redirects.
setting icmp redirects (1 on, 0 off)
/proc/sys/net/ipv4/conf/all/send_redirects 0
/proc/sys/net/ipv4/conf/default/send_redirects 0
/proc/sys/net/ipv4/conf/eth0/send_redirects 0
device eth0 has VIP 192.168.1.10
new VIP device == old VIP device, don't reinstall
device eth0 has VIP 192.168.1.10 and is UP
removing 192.168.1.10 from eth0
adding ethernet device and routing for VIP 192.168.1.10
listing ifconfig info for VIP 192.168.1.10
eth0 Link encap:Ethernet HWaddr 00:50:BA:11:34:9B
inet addr:192.168.1.10 Bcast:192.168.1.10 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:71 errors:0 dropped:0 overruns:0 frame:0
TX packets:78 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:7131 (6.9 Kb) TX bytes:9536 (9.3 Kb)
Interrupt:11 Base address:0xc800
checking VIP 192.168.1.10 is reachable from self (director): PING
192.168.1.10 (192.168.1.10) from 192.168.1.10 : 56(84) bytes of data.
64 bytes from 192.168.1.10: icmp_seq=0 ttl=255 time=82 usec
--- 192.168.1.10 ping statistics ---
1 packets transmitted, 1 packets received, 0% packet loss
round-trip min/avg/max/mdev = 0.082/0.082/0.082/0.000 ms
listing routing info for VIP 192.168.1.10
192.168.1.10 0.0.0.0 255.255.255.255 UH 40 0 0
eth0
clearing ipvsadm table
installing LVS services with ipvsadm
initialising persistence for 192.168.1.10 to N
persistence for 192.168.1.10 N
non-persistent service on 192.168.1.10:http
checking if server rip is reachable from director: PING rip
(192.168.1.5)
from 192.168.1.69 : 56(84) bytes of data.
64 bytes from rip (192.168.1.5): icmp_seq=0 ttl=128 time=194 usec
--- rip ping statistics ---
1 packets transmitted, 1 packets received, 0% packet loss
round-trip min/avg/max/mdev = 0.194/0.194/0.194/0.000 ms
displaying ipvsadm settings
IP Virtual Server version 0.8.1 (size=65536)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP lvs:http rr
-> rip:http Masq 1 0 0
checking for valid server_gw for vs-nat LVS.
NUM_SERVER_GW = 1
default gw 192.168.1.69 for the vs-nat servers is on director, good
DIRECTOR_GW=192.168.1.4
installing default gw for vs-nat
not installing a default gw for LVS_TYPE vs-nat
DIRECTOR_GW=192.168.1.4
setup_director_masq_table: Error kernel series 2.4.9-26beta unknown
not adding filter rules.
ntpd not running, won't be restarted
The location of the output files rc.lvs, mon.cf and ntp.conf is the
default
= ./
You can change this by editing the variables $rc_lvs_home, $rc_mon_home,
$rc_ntp_home
Errors: 5
Some of these errors are from tests that failed.
If you're experimenting, it's possible that the LVS will work.
If you're doing production, you can't assume that the LVS will work.
Your LVS may not be setup properly.
Warnings: 1
The configure script has encountered an unexpected situation.
Your LVS will probably run (it may not do what you want).
It would be reasonable to try your LVS first,
since it will likely work at least partially.
It is possible that the conf file has invalid information
(or the configure script has a bug).
If you suspect a bug in the script, please contact jmack@xxxxxxxx
or post to the LVS mailing list lvs-users@xxxxxxxxxxxxxxxxxxxxxx
(You can always run rc.lvs manually on director/real-servers.)
After I run the rc.lvs_nat file, I find the eth0:68, a alias of the eth0
is
lost and I can not use mozila to visit internet. I am pretty sure I do
nothing on iptables except configure and run the lvs script.
Can you tell me where is my mistake?
Regards
xiao
_______________________________________________
LinuxVirtualServer.org mailing list - lvs-users@xxxxxxxxxxxxxxxxxxxxxx
Send requests to lvs-users-request@xxxxxxxxxxxxxxxxxxxxxx
or go to http://www.in-addr.de/mailman/listinfo/lvs-users
|
