|
Wow, i'm going to try all this and tell you tomorrow how did it go. You're a
genious by the way
Thank you a lot
L.S. Keijser-2 wrote:
>
> Hi,
>
> I'm replying to you and to the lvs-users list so everyone can
> participate and help. It's a fairly long reply with detailed
> instructions on how to get it working. I could just point you to the
> HOWTO (as i already did) but i'm in a good mood. Also, since it's so
> long and detailed, i hope i got it right else it's a waste of time :P
>
> Oh and i'm going to make a lot of assumptions while replying, so please
> correct me if i'm wrong:
>
> On Thu, 2009-10-22 at 12:38 -0700, partysoft@xxxxxxxxx wrote:
>> Thank you Léon for the reply. I apreciate it so much.
>> Yes i actually have 3 public ip's like (none are with 192..)
>> XX.XX.XX.234 (this is the lvs..)
>
> by 'the lvs' i assume you mean 'the director'
>
>> XX.XX.XX.235 real server (web ngix)
>> YYY.YYY.YYY.163 real server (web apache) - I don't really care about
>> this one, i can move it into the
>
> into the .. ? cat caught your tongue? :P
>
>> we will use XX.XX.XX.236 as virtual..(there isn't an ip on the net with
>> that number up). of course it will be simpler to use a 192.. but, i have
>> tried that also ,and no luck
>
> I assume that by 'virtual' you mean Virtual IP configured on the
> director.
>
>> same subnet as the first 2 ones, i just want to make it work from the 234
>> -> 235..but it gives me a timeout on the browser...
>
> You mean from .236 -> .235 because clients won't connect to the IP of
> the director. Instead they'll connect to the VIP.
>
>> Here's what i did:
>>
>> [root@linux ~]# cat /etc/ha.d/ldirectord.cf
>> checktimeout=3
>> checkinterval=10
>> autoreload=yes
>> logfile="/var/log/ldirectord.log"
>> quiescent=no
>
> I'm not sure 'quiescent=no' is a valid option in ldirectord.cf .. What
> were you trying to accomplish here?
>
>> virtual=XX.XX.XX.236:80
>> fallback=127.0.0.1:80
>> real=XX.XX.XX.235:80 gate
>> real=YYY.YYY.YYY.235:80 gate
>
> Where does the YYY.YYY.YYY.235 come from? Assuming X != Y, this will
> never work as the two realservers are in different subnets. Again i'm
> assuming this because of your ifconfig post later in this mail. Either
> move the 2nd realserver into the subnet, leave it out, or extend your
> subnet to include it (probably not possible).
>
>> service=http
>> request="test.html"
>> receive="Still alive"
>> scheduler=rr #here i've tried with172.18.24.15 wlr as well
>
> The scheduler is irrelevant for now. Let's just first try to get it
> working period. Anyway, 'wlr'? I'm not even sure this is a valid
> scheduler. Don't you mean 'wlc' or 'wrr'? :)
>
>> protocol=tcp
>> checktype=negotiate
>>
>> [root@linux ~]# /usr/sbin/ldirectord -d /etc/ha.d/ldirectord.cf start
>
> It's better (to learn LVS) if you don't use ldirectord for now, but ok,
> let's try it anyway :P
>
> -snip heartbeat output-
>
>> If i go to the webserver i can see that ldirector is actually testing the
>> test.html..every 10 seconds like in the conf
>
> Good, at least the director can access one of the realservers.
>
>> I am sure that is because of the configurations of the IPs and the
>> aditional eth0:0 and lo:0 and that's why it doesn't work, i will paste
>> everything that i did, maybe, just maybe you can help me out on this one,
>> i'm really stuck..probably because i don't know lots of stuff on how the
>> OSI layer is build and how arp works
>
> Okay, tiny summary of what's supposed to happen in LVS-DR:
>
> 1) client sends request to VIP
> 2) director receives packet, checks LVS table for available realserver
> and forwards the packet to it without changing destination_ip
> 3) realserver receives packet and sees destination_ip matches the
> configured ip on its loopback device
> 4) realserver handles request and replies to src_address (the original
> client) thereby using its default gateway, bypassing the director
> 5) client receives reply
>
> What probably happened is that you didn't solve the ARP problem and
> instead of receiving a reply from the IP configured on the realserver's
> loopback device (that's the VIP, the same one configured on the
> director), the realserver's RIP replies to the client. Your client never
> sent a request to _that_ IP so it drops the packet, endlessly waiting
> for a reply from the VIP.
>
>> Aditional Network conf..
>> XX.XX.XX.234 (this is the lvs..) is spawned on eth1..
>> so i spawned another eth1:0
>> [root@linux ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth1:0
>> DEVICE=eth1:0
>> IPADDR=XX.XX.XX.236 # this is from the same subnet and i doesn't
>> conflict with an existent one
>> NETMASK=255.255.255.0
>> NETWORK=XX.XX.XX.0
>> BROADCAST=XX.XX.XX.255
>> GATEWAY=XX.XX.XX.233 # i've put the same gateway as the default ip
>> XX.XX.XX.234 had
>> ONBOOT=yes
>>
>> i also enabled port forwarding
>
> Port forwarding isn't required for LVS-DR.
>
>> net.ipv4.ip_forward = 1
>> net.ipv4.conf.default.rp_filter = 1
>> net.ipv4.conf.default.accept_source_route = 0
>> kernel.sysrq = 0
>> kernel.core_uses_pid = 1
>> net.ipv4.tcp_syncookies = 1
>> kernel.msgmnb = 65536
>> kernel.msgmax = 65536
>> kernel.shmmax = 68719476736
>> kernel.shmall = 4294967296
>>
>> And i did the modprobe with all those modules for IPV
>>
>> modprobe ip_vs_dh
>> modprobe ip_vs_ftp
>> modprobe ip_vs_dh
>> modprobe ip_vs_ftp
>> modprobe ip_vs
>> modprobe ip_vs_lblc
>> modprobe ip_vs_lblcr
>> modprobe ip_vs_lc
>> modprobe ip_vs_nq
>> modprobe ip_vs_rr
>> modprobe ip_vs_sed
>> modprobe ip_vs_sh
>> modprobe ip_vs_wlc
>> modprobe ip_vs_wrr
>
> IPVS will load the module it requires for the configured scheduler
> automatically. It's not necessary to load any module manually.
>
>> and that's all i did for the LVS server..
>>
>> Now for the webserver
>> XX.XX.XX.235 (this is the lvs..) is spawned on eth0..
>> root@linux ~]# cat /etc/sysconfig/network-scripts/ifcfg-lo:0
>> DEVICE=lo:0
>> IPADDR=XX.XX.XX.236
>> NETMASK=255.255.255.255
>> NETWORK=XX.XX.XX.XX.0
>> BROADCAST=XX.XX.XX.255
>> ONBOOT=yes
>> NAME=loopback
>
> AFAIK it's best not to use the sysconfig scripts to create the loopback
> device on the realserver. RedHat does an ARPING to determine if the
> interface you're trying to configure is already up. It might confuse
> things. You could just as easily configure everything
> from /etc/rc.local. See below the next bit:
>
>> and
>>
>> net.ipv4.ip_forward = 0
>> net.ipv4.conf.lo.arp_ignore = 1 #here i have tried with eth0 instead of
>> lo, no luck..
>> net.ipv4.conf.lo.arp_announce = 2 #here i have tried with eth0 instead
>> of lo, no luck..
>> net.ipv4.conf.all.arp_ignore = 1
>> net.ipv4.conf.all.arp_announce = 2
>
> Okay, you're starting okay in trying to solve the ARP problem. But
> you're really not... Configure arp ignore/announce and the loopback
> device from within /etc/rc.local like this:
>
> # solve the 'ARP problem'
> echo 1 > /proc/sys/net/ipv4/conf/lo/arp_ignore
> echo 1 > /proc/sys/net/ipv4/conf/eth0/arp_ignore
> echo 2 > /proc/sys/net/ipv4/conf/lo/arp_announce
> echo 2 > /proc/sys/net/ipv4/conf/eth0/arp_announce
> /sbin/ifconfig lo:0 XX.XX.XX.236 netmask 255.255.255.255 up
>
> (reboot your realserver after this, or bring down lo:0 and
> run /etc/rc.local)
>
>> net.ipv4.conf.default.rp_filter = 1
>> net.ipv4.conf.default.accept_source_route = 0
>> kernel.sysrq = 0
>> kernel.core_uses_pid = 1
>> net.ipv4.tcp_syncookies = 1
>> kernel.msgmnb = 65536
>> kernel.msgmax = 65536
>> kernel.shmmax = 68719476736
>> kernel.shmall = 4294967296
>>
>> here i've tried with ip forward 0 and 1 , no luck the requests simply
>> don't reach this server only the direct ones
>
> You don't configure ip_forward on the realservers.
>
>>
>> Now i've understand that this is an ARP problem, and as CentOS doesn't
>> support the arp hidden flag on sysctl , i tried with
>> /etc/init.d/arptables_jf
>
> -snip arptables output-
>
> Again, assuming you have a fairly recent kernel, you don't need
> arptables. Just for fun, please post your kernel version.
>
>> -----------------------------------------------
>>
>> i've probed with ipvsadm or something like it, to see the active
>> connections, and they are always to 0
>>
>> i've modprobed here the same modules, no luck..
>>
>> So from this point i'm really stuck and don't know what to do...
>>
>> Here's the ifconfig from both servers if that helps
>> from the LVS (xx.234)
>>
>> eth1 Link encap:Ethernet HWaddr 00:1B:21:46:3E:A9
>> inet addr:XX.XX.XX.234 Bcast:XX.XX.XX.239
>> Mask:255.255.255.248
>
> Okay, this pretty much rules out the possibility that both your
> realservers are in the same subnet, so fix that first by either removing
> one that isn't in the same subnet as the director, or by moving it into
> the subnet.
>
>> eth1:0 Link encap:Ethernet HWaddr 00:1B:21:46:3E:A9
>> inet addr:XX.XX.XX.236 Bcast:XX.XX.XX.255 Mask:255.255.255.0
>
> Your configured VIP is in a different subnet than your real IP. Probably
> doesn't matter much in this case though, but still..
>
> -snip rest of output-
>
>> here's the one from the webserver
>>
>> eth0 Link encap:Ethernet HWaddr 00:24:1D:72:61:AB
>> inet addr:XX.XX.XX.235 Bcast:XX.XX.XX.239
>> Mask:255.255.255.248
>
> -snip rest of eth0 and lo output-
>
>> lo:0 Link encap:Local Loopback
>> inet addr:XX.XX.XX.236 Mask:255.255.255.255
>> UP LOOPBACK RUNNING MTU:16436 Metric:1
>
> Good, it has the VIP configured.
>
> So after all these changes/checks/reboots, run this command from a
> client (not the director or any of the realservers!) :
>
> $ arping XX.XX.XX.236
>
> You should get a reply from 00:1B:21:46:3E:A9 (MAC on the director). If
> you get any reply from 00:24:1D:72:61:AB (MAC on the realserver) you
> haven't solved the ARP problem yet. Assuming (here we go again) that you
> have now configured the lo:0 on the realserver correctly (and removed it
> from /etc/sysconfig/network-scripts/ifcfg-lo:0 !!), clear the arp cache
> on the client:
>
> $ arp -d XX.XX.XX.236
>
> and try the arping command again.
>
> Also, disable any firewalls on both director and realservers while
> setting things up. You can always later lock it down (while keeping an
> eye on functionality). This way it won't disturb setting up LVS.
>
> And if you rather not use ldirectord (recommended for first-time usage):
>
> $ service ldirectord stop
> $ ipvsadm -A -t XX.XX.XX.236:80 -s rr
> $ ipvsadm -a -t XX.XX.XX.236:80 -r XX.XX.XX.235:80 -g -w 1
>
> Then from a client (not the director or realserver) try it out:
>
> $ telnet XX.XX.XX.236 80
>
> If you get a response like this:
>
> Trying XX.XX.XX.236...
> Connected to XX.XX.XX.236.
> Escape character is '^]'.
>
> Then it's working.
>
> Good luck :)
>
> --
> Léon
>
>
> _______________________________________________
> Please read the documentation before posting - it's available at:
> http://www.linuxvirtualserver.org/
>
> LinuxVirtualServer.org mailing list - lvs-users@xxxxxxxxxxxxxxxxxxxxxx
> Send requests to lvs-users-request@xxxxxxxxxxxxxxxxxxxxxx
> or go to http://lists.graemef.net/mailman/listinfo/lvs-users
>
--
View this message in context:
http://www.nabble.com/LdirectorD-LVS-and-CentOS-Fedora-RedHat-tp26004219p26018186.html
Sent from the LVS mailing list archive at Nabble.com.
_______________________________________________
Please read the documentation before posting - it's available at:
http://www.linuxvirtualserver.org/
LinuxVirtualServer.org mailing list - lvs-users@xxxxxxxxxxxxxxxxxxxxxx
Send requests to lvs-users-request@xxxxxxxxxxxxxxxxxxxxxx
or go to http://lists.graemef.net/mailman/listinfo/lvs-users
|
