|
Greetings,
Please excuse if there is answer to this in a FAQ somewhere I need to get the LVS working for this project pretty quick and hope someone can point me in the right direction I'd greatly appreciate it..
I am attempting to configure an LVS cluster and I have the FOS component working just great BUT I can't get the LVS router to redirect requests to http. When I have UDP selected of course I can resolve pull pages from the HTTP server on 10.2.9.50 but when I enable TCP and the ipvsadm routing table the redirection isn't working. Running Redhat 6.2 with all the patches and latest RPM's.
Here's the lvs.cf:
primary = 10.2.9.21
service = lvs
rsh_command = rsh
backup_active = 1
backup = 10.2.9.17
heartbeat = 1
heartbeat_port = 1050
keepalive = 6
deadtime = 18
network = nat
nat_router = 10.11.1.254 eth1:1
virtual server1 {
active = 1
address = 10.2.9.50 eth0:1
port = 80
send = "GET / HTTP/1.0\r\n\r\n"
expect = "HTTP"
load_monitor = ruptime
scheduler = rr
protocol = tcp
timeout = 5
reentry = 10
server innovyx3 {
address = 10.11.1.3
active = 1
weight = 1
}
server innovyx5 {
address = 10.11.1.5
active = 1
weight = 1
}
}
Things I've tried:
You'll notice the netmasks for eth0:1 and eth1:1 are different from eth0 and eth1 I tried duplicating these with no luck.
Ip forwarding and ip defag is enabled
I can ping the NAT router and the LVS IP
I have the following:
LVS Cluster Server 1 - 10.2.9.21
eth0 Link encap:Ethernet HWaddr 00:A0:C9:66:18:58
inet addr:10.2.9.21 Bcast:10.2.255.255 Mask:255.255.0.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:349228 errors:0 dropped:0 overruns:0 frame:0
TX packets:18853 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
Interrupt:11
eth0:1 Link encap:Ethernet HWaddr 00:A0:C9:66:18:58 <***Virtual Server IP
inet addr:10.2.9.50 Bcast:10.255.255.255 Mask:255.0.0.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Interrupt:11
eth1 Link encap:Ethernet HWaddr 00:A0:C9:26:A3:3F
inet addr:10.11.1.1 Bcast:10.11.255.255 Mask:255.255.0.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:256919 errors:0 dropped:0 overruns:0 frame:0
TX packets:302688 errors:0 dropped:0 overruns:0 carrier:0
collisions:8 txqueuelen:100
Interrupt:11 Base address:0x2000
eth1:1 Link encap:Ethernet HWaddr 00:A0:C9:26:A3:3F <****NAT ROUTER IP
inet addr:10.11.1.254 Bcast:10.255.255.255 Mask:255.0.0.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Interrupt:11 Base address:0x2000
Cluster Server 2: - 10.2.9.17
eth0 Link encap:Ethernet HWaddr 00:50:8B:B0:09:BC
inet addr:10.2.9.17 Bcast:10.2.255.255 Mask:255.255.0.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:347097 errors:0 dropped:0 overruns:0 frame:0
TX packets:16258 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
Interrupt:11
eth1 Link encap:Ethernet HWaddr 00:A0:C9:1F:4E:D9
inet addr:10.11.1.2 Bcast:10.11.255.255 Mask:255.255.0.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2776 errors:0 dropped:0 overruns:0 frame:0
TX packets:425 errors:0 dropped:0 overruns:0 carrier:0
collisions:4 txqueuelen:100
Interrupt:11 Base address:0x2000
Ipvsadm route:
TCP 10.2.9.50:www rr
-> innovyx5:www Masq 1 0 0 - 10.11.1.5
-> innovyx3:www Masq 1 0 0 - 10.11.1.3
ipchains route on 10.2.9.21:
target prot opt source destination ports
MASQ all ------ 10.2.0.0/16 anywhere n/a
Ipchains on 10.2.9.17:
target prot opt source destination ports
MASQ all ------ 10.2.0.0/16 anywhere n/a
So from the looks of it everything works great the FOS will failover with no problems to 10.2.9.17 and switch back just the same but I cannot get it to route http between my 2 web servers. I am out of things to try at the moment so any light you can shed on the subject please beam it my way.
Marcus Patman
MTG - Network Services
patmanm@xxxxxxxxxxxxxxxxxxxxxxxxxxxx
| 