[lvs-users] ultramonkey_setup: I can't ping or ssh into my real_servers(centOS_5, Fedora7)

["j j" <rampeters@xxxxxxxxx>]

ssh and ping is not working on both real_server machines.  I can't do
"ping 192.168.0.4" or ssh into real_server machines.  I haven't turn
on the linux_director yet.  After I followed the instructions on
http://www.ultramonkey.org/3/topologies/hc-ha-lb-eg.html, and rebooted
the real_server machine, and tried ssh, and got this:

[me@localhost ~]$ ssh me@xxxxxxxxxxx
ssh: connect to host 192.168.0.4 port 22: No route to host


Right now I have omitted setup info on linux_director.


My setup for High Capacity High Availability and Load Balancing:

Gateway_IP_Address: 192.168.0.1
virtual_IP_Address: 192.168.0.240
Linux_Director_1: 192.168.0.2
Real_Server_1: 192.168.0.4
Real_Server_2: 192.168.0.5


On my real servers, my setup is like this:
Real Server1 (for Real_server2, I replace below content that have
192.168.0.4 with 192.168.0.5):

[root@localhost me]# /sbin/arptables -L -v -n
Chain IN (policy ACCEPT 9 packets, 252 bytes)
 pkts bytes target     in     out     source-ip
destination-ip       source-hw          destination-hw     hlen   op
      hrd        pro
    0     0 DROP       *      *       0.0.0.0/0
192.168.0.240        00/00              00/00              any
0000/0000  0000/0000  0000/0000

Chain OUT (policy ACCEPT 18 packets, 504 bytes)
 pkts bytes target     in     out     source-ip
destination-ip       source-hw          destination-hw     hlen   op
      hrd        pro
    0     0 mangle     *      eth0    192.168.0.240        0.0.0.0/0
         00/00              00/00              any    0000/0000
0000/0000  0000/0000 --mangle-ip-s 192.168.0.4

Chain FORWARD (policy ACCEPT 0 packets, 0 bytes)
 pkts bytes target     in     out     source-ip
destination-ip       source-hw          destination-hw     hlen   op
      hrd        pro


Configured Loopback Interface:

/etc/sysconfig/network-scripts/ifcfg-lo:0:

DEVICE=lo:0
IPADDR=192.168.0.240
NETMASK=255.255.255.255
NETWORK=192.168.0.0
BROADCAST=192.168.0.255
ONBOOT=yes
NAME=loopback


Default Route:

/etc/sysconfig/network-scripts/ifcfg-eth0:

DEVICE=eth0
BOOTPROTO=static
IPADDR=192.168.0.4
NETMASK=255.255.255.0
NETWORK=192.168.0.0
BOARDCAST=192.168.0.255

#GATEWAY=192.168.0.3
GATEWAY=192.168.0.1
HWADDR=00:45:25:24:46:EF
ONBOOT=yes

If I do ifconfig, I get the following:

[root@localhost me]# /sbin/ifconfig
eth0      Link encap:Ethernet  HWaddr 00:45:25:24:46:ef
          inet addr:192.168.0.4  Bcast:192.168.0.255  Mask:255.255.255.0
          inet6 addr: ee80::203:25ad:cc42:46da/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:50 errors:0 dropped:0 overruns:0 frame:0
          TX packets:72 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:13486 (13.1 KiB)  TX bytes:10340 (10.0 KiB)
          Interrupt:17

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:9590 errors:0 dropped:0 overruns:0 frame:0
          TX packets:9590 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:69607264 (66.3 MiB)  TX bytes:69607264 (66.3 MiB)

lo:0      Link encap:Local Loopback
          inet addr:192.168.0.240  Mask:255.255.255.255
          UP LOOPBACK RUNNING  MTU:16436  Metric:1

Why does lo:0 has only three lines as comapred to other ones?

thanks.