|
I am also new to LVS and am starting with a very similar configuration (albeit
with apache) that is getting a timeout too. Not sure if it's the same problem
as you have. I'll send config details tomorrow if it's not resolved by then
(or is unrelated to the problem you are having).
-----Original Message-----
From: lvs-users-bounces@xxxxxxxxxxxxxxxxxxxxxx on behalf of redirecting decoy
Sent: Tue 2/1/2005 11:24 PM
To: lvs-users@xxxxxxxxxxxxxxxxxxxxxx
Subject: Trouble setting up LVS/TUN
Hello,
I am new to LVS and am having some trouble getting it
setup and running.
I am attempting to do Tunneling with 2 real machines,
and 1 director (running inside of a uml).
Here is my setup and what I did in an attempt to get
lvs working.
On Director:
########################################################
Interfaces:
eth0 Link encap:Ethernet HWaddr
FE:FD:C0:A8:0A:6E
inet addr:192.168.10.110
Bcast:192.168.10.255 Mask:255.255.255.0
eth0:0 Link encap:Ethernet HWaddr
FE:FD:C0:A8:0A:6E
inet addr:192.168.10.111
Bcast:192.168.10.111 Mask:255.255.255.255
eth1 Link encap:Ethernet HWaddr
FE:FD:0A:01:02:02
inet addr:10.1.2.2 Bcast:10.255.255.255
Mask:255.255.255.0
eth2 Link encap:Ethernet HWaddr
FE:FD:0A:01:03:02
inet addr:10.1.3.2 Bcast:10.255.255.255
Mask:255.255.255.0
lo inet addr:127.0.0.1 Mask:255.0.0.0
----------------------------------------------------------------------------
The directors Real IP (RIP) is 192.168.10.110. I
want the VIP to be
192.168.10.111, which I setup using the following
command:
"ifconfig eth0:0 192.168.10.111 netmask
255.255.255.255 broadcast 192.168.10.111 up"
eth1 and eth2 are on private addresses (10.1.x.x) to
access my Real Servers.
I have 2 real servers that I want to use. I'll call
them N1 and N2 with the ip's
10.1.2.254 and 10.1.3.254.
So I setup lvs using the following:
ipvsadm -A -t 192.168.10.111:80
ipvsadm -a -t 192.168.10.111:80 -r 10.1.2.254:80 -i
ipvsadm -a -t 192.168.10.111:80 -r 10.1.3.254:80 -i
ipvsadm -L -n gives me the following:
----------------------------------------------
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight
ActiveConn InActConn
TCP 192.168.10.111:80 wlc
-> 10.1.3.254:80 Tunnel 1 0
0
-> 10.1.2.254:80 Tunnel 1 0
0
----------------------------------------------
So far so good. Next thing I did was setup the Real
servers.
On the Real Servers:
########################################################
Interfaces: N1 and N2
eth0 Link encap:Ethernet HWaddr
00:60:08:16:0C:0C
inet addr:10.1.(2,3).254
Bcast:10.255.255.255 Mask:255.0.0.0
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
tunl0 Link encap:IPIP Tunnel HWaddr
inet addr:192.168.10.111
Mask:255.255.255.255
UP RUNNING NOARP MTU:1480 Metric:1
RX packets:14 errors:0 dropped:0 overruns:0
frame:0
TX packets:0 errors:0 dropped:0 overruns:0
carrier:0
collisions:0 txqueuelen:0
RX bytes:780 (780.0 b) TX bytes:0 (0.0 b)
########################################################
to setup the real servers I did:
modprobe ipip
ifconfig tunl0 0.0.0.0 up
ifconfig tunl0 192.168.10.111 netmask 255.255.255.255
broadcast 192.168.10.111 up
then as I am using a 2.4.26 kernel, I used
arp_announce and arp_ignore to solve the arp
problem with the following commands:
echo '2' > /proc/sys/net/ipv4/conf/all/arp_announce
echo '2' > /proc/sys/net/ipv4/conf/tunl0/arp_announce
echo '1' > /proc/sys/net/ipv4/conf/all/arp_ignore
echo '1' > /proc/sys/net/ipv4/conf/tunl0/arp_ignore
Then finally, on the real server's I turned off apache
and ran netcat on port 80:
"nc -v -v -l -p 80"
Now, according to documentation, everything I have
done should work. However from an
external machine, (192.168.10.15), if I attempt to
connect to 192.168.10.111:80 (VIP),
my connection just hangs there and eventually times
out. Did I miss something in the configuration?
Or maybe I did something wrong? Any help would be
greatly appreciated.
Thanks in advance,
-R.D.
__________________________________
Do you Yahoo!?
Take Yahoo! Mail with you! Get it on your mobile phone.
http://mobile.yahoo.com/maildemo
|
